怎樣防止樓承板表面與地面或空中的潮氣接觸呢？這個問題如果不好好解決的話，就會出現與您的施工期間之內，可能會造成樓承板工程質量的不好，下面就來看看吧。

How to prevent the surface of floor bearing plate from contacting with the moisture on the ground or in the air? If this problem is not properly solved, it will occur during your construction period, which may cause poor quality of the floor support plate project. Let's take a look at it below.

濟南樓承板在安裝時可利用位于屋面板下方用于隔熱的反射箔，也可以簡單的用作防潮，只需在其搭接處用防潮粘帶密封即可。搭接的距離應大于100mm，定位箔片層時，保持緊密接觸，使防潮膠帶充分的發揮作用。箔片層必須覆蓋在屋頂?shù)闹沃g。

Jinan floor support plate can be installed by using the reflective foil under the roof panel for heat insulation, or simply used as moisture-proof. It only needs to be sealed with moisture-proof adhesive tape at its lap. The overlapping distance shall be greater than 100mm. When positioning the foil layer, keep close contact to make the moisture-proof tape fully play its role. The foil layer must cover between the supports of the roof.

如果發生此情況，冷凝就會在箔片的下方形成了。而為了減少樓承板在存放時下面的濕氣凝聚，也必須在樓承板成型設備的下方與樓承板下方設置防潮板，以防止鋼板下表面與地面或空中的潮氣接觸。

If this happens, condensation will form under the foil. In order to reduce the condensation of moisture under the floor support plate during storage, moisture-proof plates must also be set under the floor support plate forming equipment and under the floor support plate to prevent the lower surface of the steel plate from contacting with the moisture on the ground or in the air.

樓承板的表面層鋼板比所接觸的空氣冷，或者空氣中所帶來的水汽凝聚在鋼板上表面的時候，樓承板的下面就產生了一些冷凝。這種正常性的現象是必然不可預料，許多建筑物都面臨著此類問題。

The steel plate on the surface layer of the floor support plate is colder than the contact air, or when the water vapor brought by the air condenses on the upper surface of the steel plate, some condensation occurs under the floor support plate. This normal phenomenon is inevitable and unpredictable, and many buildings are facing such problems.

比如在涼爽晴朗的夜晚，鋼板將向空氣中輻射的熱量，直至鋼板的溫度降至周圍空氣的溫度；有時氣溫只有5℃。但鋼板甚至可以繼續輻射，并保持比和它接觸的空氣冷，直到周圍的空氣溫度升高。

For example, on a cool and sunny night, the steel plate will radiate heat into the air until the temperature of the steel plate drops to the temperature of the surrounding air; Sometimes the temperature is only 5 ℃. But the steel plate can even continue to radiate and remain colder than the air in contact with it until the ambient air temperature rises.

此外要知道樓承板凹凸不平的作用是增大摩擦系數。樓承板(鋼承板，建筑壓型鋼板)是采用鍍鋅鋼板經輥壓冷彎成型，其截面成V型、U型、梯形或類似這幾種形狀的波形，主要用作永久性模板，也可被選為其他用途。更多相關事項就來我們網站http://www.95fjrc.com咨詢看看吧。

In addition, it is necessary to know that the function of uneven floor bearing plate is to increase the friction coefficient. Floor bearing plate (steel bearing plate, building profiled steel plate) is formed by rolling and cold bending of galvanized steel plate. Its cross section is V-shaped, U-shaped, trapezoidal or similar waveforms. It is mainly used as permanent formwork and can also be selected for other purposes. For more information, please visit our website http://www.95fjrc.com Let's consult.